Intersmooth7460HSSPC Wuxi self-polishing copolymer antifouling paint warehouse has a large stock, welcome to inquire. Intersmooth 7460HS SPC Wuxi self-polishing copolymer antifouling paint, a high-solids, high performance, Wuxi self-polishing copolymer (SPC) antifouling paint. Especially for the need to reduce solvent emissions area. Product Overview specifically designed for ocean-going vessels. For repair and maintenance. Intended use BEA754- brown, BEA757- red 54% ± 2% (ISO 3233: 1998) 125 micron dry film thickness (231 microns wet) at 125 microns dry film thickness Theoretical spreading rate of 4.32 m 2 / liter, allow appropriate loss factors Airless Spray, Brush, Roller PRODUCT INFORMATION Volume Solids Typical Film Thickness Theoretical Coverage Method of Application Finish / Sheen Not applicable Part B (hardener) NA NA flashpoint single mixing ratio Component 25 ° C Overcoating Data - see "limited" one color dry material substrate temperature -5 ° C 5 ° C 25 ° C 35 ° C Dry [ISO 1517: 73] 120 minutes 60 minutes 40 minutes 30 minutes before launching (0-36 months program) 30 hours 20 hours 16 hours 10 hours before the water (48-60 month program) 48 hours 36 hours 24 hours when recoating following products -5 ° C 5 ° C 25 ° C 35 ° C Min Max Min Max Min Max Min Max in the following cases, time 0-36 months before launching the program must refer to the time of 48-60 months before launching the program: 1) anti-fouling paints contain any supporting total dry film thickness greater than 150 microns in a single coat, or 2) the ship speed higher than 15 notes Intersmooth 7460HS SPC 0-36 month program 28 days 12 hours 4 hours 6 hours 28 days 28 days 28 days 3 hours Intersmooth 7460HS SPC 48-60 month program - - 18 hours 28 days 12 hours 28 days 9 hours 28 days REGULATORY DATA VOC VOC values ??are typical, are provided for guidance only. As such they may change color and normal manufacturing tolerances such factors and changes. 425 g / liter (original paint) (EPA Method 24) 226 g / kg (original liquid paint). When used as part of an approved scheme, this product has the following certification: Product recognized by the following classification societies, in line with the relevant control of harmful anti-fouling systems on board an international convention, 2001 (AFS 2001):? Lloyd's Register of Shipping Agency (Lloyds Register)? DNV (Det Norske Veritas) For more information, please contact your Department of International Paint (International Paint) representative. SYSTEMS AND COMPATIBILITY certificate in accordance with the standard "global marine coatings supporting (Worldwide Marine Specifications)" use. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate subject, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. Surface treatment overhaul Intersmooth 7460HS SPC should always be applied over a recommended primer. The primer surface should be dry and free from contamination, Intersmooth 7460HS SPC must be applied (see the relevant product data sheet) within the specified overcoating intervals. Breakdown, damage etc. should be prepared to the specified standard (eg: SSPC-SP10), and in the pre-construction Intersmooth 7460HS SPC, primed. Maintenance Intersmooth 7460HS SPC construction in itself: the ship entered the dock, before it dries using a fan-jet lance injection high pressure fresh water close to the surface (3,000 pounds / square inch, 211 kg / cm) wash to clean up the entire area. See the recommended anti-corrosive coating systems and construction Intersmooth 7460HS SPC within the prescribed primer recoating intervals (see the relevant primer product specification). International Paint (International Paint) Wuxi antifouling paint, construction on Intersmooth 7460HS SPC International Paint (International Paint) Intersmooth SPC antifouling paint antifouling paint or competitor: best suited for specific recommendations to protect the surface of the paint system to be relevant, Ask at your International Paint (International Paint) representative. Wuxi self-polishing copolymer antifouling paint coating for the one-component coating, pre-construction should be thoroughly with power agitator. Application by brush is recommended for small areas. Multiple coats may be required to achieve specified film thickness. By roller is recommended for small areas. Multiple coats may be required to achieve specified film thickness. Not recommended. Only in exceptional circumstances, the use of international brand GTA007 (by volume, the maximum amount of 5%). Dilution should not exceed local environmental legislation allows. International GTA007 In the event welding or flame cutting is performed on metal coated with this product in, will emit dust and smoke, use of appropriate personal protective equipment and adequate local exhaust ventilation. Recommended nozzle size 0.54-0.80 mm (21-31 thou) Total output fluid pressure at spray tip not less than 190 kg / cm 2 (2700 lbs / square inch) is not recommended by conventional spray is. APPLICATION Mixing Airless Spray Conventional Spray Brush Roller Thinner Cleaner Welding Work Stoppages and Cleanup GTA007 Thoroughly flush all equipment. All unused material should be stored in closed containers. Paint containers are not filled after storage may occur viscosity increase of the phenomenon. Paint should be filtered before use. All work involving the application and use of the product concerned shall be conducted in accordance with national standards and regulations on health, safety and environmental protection. And all of the products mentioned in the specification product names are AkzoNobel (Akzo Nobel)